Effects of Unilateral Robotic Assistance on Compensation Strategies and Muscular Activity During Hemiparetic Gait

• Materials: The investigators have developed a Knee-Ankle-Foot orthosis (KAFO) composed of two joints aligned to the knee and ankle of the user. The length of its bars and the positions of its braces can be tailored to the anthropometry of different users. The knee joint is actuated by a DC brushless motor EC-60 flat 408057 (Maxon ag, Switzerland) coupled with a harmonic drive CSD-20-160-2AGR (Harmonic Drive LLC, EE.UU.). The transmission ratio of 1:60 of this system enables the application of a mean torque of 35Nm. The ankle joint of the prototype remains non-actuated and unlimited, enabling its free movement in the sagittal plane. The total weight of the KAFO is about 4kg.

The prototype is equipped with sensors that provide information on system variables that are used for its control in real-time, such as the flexion angle of the robot joint or the interaction torque between user and robot. In addition, the gait kinematic of the user is measured by Inertial Measurement Units (IMUs) and the contact of both feet with the floor by Force Sensing Resistors (FSRs).

The system uses an Adaptive Frequency Oscillator to estimate the continuous gait phase of the contralateral limb and synchronically assists the paretic leg by inducing a healthy gait pattern. The action of the robot depends on the gait phase of the assisted leg: during the stance phase, the robot reinforces the limb so the system composed of the leg and the exoskeleton can load the user's weight and not collapse, while during the swing phase the robot guides the limb's movement according to the Assisted-As-Needed (AAN) paradigm creating a force tunnel around the prescribed trajectory.

• Procedures:

The experimental protocol is divided in three sessions. During all of them, the patient will walk on a treadmill commanded by the physiotherapist while wearing a safety harness to avoid falls and while wearing the robotic exoskeleton in the paretic leg. During the second and third sessions, electromyography will also be acquired by using surface electrodes (Trigno System, Delsys Inc.) and according to the SENIAM guidelines. The muscle activity of Rectus Femoris, Biceps Femoris Long Head, Tibialis Anterior and Medial Gastrocnemius of both legs will be measured through this method. Each experimental session is described next:

• - Training session: The patient will wear the robotic exoskeleton to familiarize with the action of the device. Comfortable and maximum velocities will be identified for each subject.
• - Ramp Velocity Session: the session will be divided into five trials: (a) Pre, the patient will not wear the device; (b) Free, the patient will wear the robot but it is mechanically decoupled so it will enable the free knee movement; (c) Active, the robot will assist the gait until 75% maximum gait velocity ; (d) MaxActive, the robot will assist the gait until maximum gait velocity ; and (e) Post, the patient will repeat the Pre condition. Velocity will increase from a comfortable velocity to the maximum and then come back to the comfortable one.
• - Random Velocity session: the session will be divided into the same trials than the Ramp Velocity Session.

The difference between RampVel and RandomVel sessions will be the sequence of gait speeds at which the patient will walk. During RampVel, five velocity steps will be defined from comfortable to maximum velocity with or without exo (depending on the trial) and coming back to comfortable velocity. During RandomVel, the same range of velocity will be used, but defining five steps in the whole range and setting them in a random order. In both sessions, each gait speed step will last one minute, therefore, all trials will last five minutes. Trials Free, Active and MaxActive will be also randomly ordered in each session.

Between trials, patients will rest during 10 minutes to avoid summation effects. Each session will occur in different days, leaving 1 or 2 days in between.

• Intervention providers A physiotherapist and an engineer will be present during the trials. The first will be responsible of assessing the basal gait of the subjects and evaluating his/her state while the assistance is provided. The engineer will be responsible of managing the device and recording the data.

Both researchers monitor fidelity to the intervention by direct supervision.

• Modes of delivery The protocol is provided to one participant at a time. Each patient completes the protocol once.
• Location Hospital Beata María Ana (Madrid, Spain)
• Tailoring and modifications The protocol remains unaltered across applications. The only adaptation to patients is the choice of the comfortable and maximum gait speeds for the trials.

Inclusion criteria

Ischemic or haemorrhagic stroke that lead to hemiplegic gait

Exclusion criteria

• Acute musculoskeletal diseases
• Peripheral vascular diseases
• Acute cardiopulmonary diseases
• Acute neurological diseases
• Excessive spasticity in any joint of the lower limb (Ashworth scale> 2)
• Joint mobility restriction of lower limb joints due to any cause
• Pain due to impaired mobility of the lower limb
• Inability to use robotic exoskeleton prototypes due to his/her health condition.