Spinal Straightness, Posture And Balance, Physical Performance And Energy Consumption In Individuals With Stroke

Primary outcomes

1. Use of Spinal Mouse

   Time frame: day 1

   The SM device is started at the 7th cervical vertebra and advanced to the anal line. During the measurement, the mouse is lowered from the skin surface at a constant speed from top to bottom at the midpoint of the processus spinosus. Individuals are asked to assume the upright, maximal flexion, maximal extension positions in sequence.

   The relevant parameters in each position are thoracic curvature angle, lumbar curvature angle, sacrum-hip angle, tilt angle, mobility assessment (from extension to flexion position). The data transferred by the SM device to the computer via Bluetooth is analyzed and the angular deviation between each vertebra is calculated by the SM software as an angle value. The raw data of the wireless and handheld mouse is transferred to the computer via bluetooth and the data is analyzed by the SM software.

2. Postural Symmetry Index

   Time frame: day 1

   A form of measurement in which two scales are used to calculate the weight transferred to the intact and paralyzed limb. The values obtained as a result of the test are calculated with the following formulas. In this index, percentages close to 0 define equal symmetry and good postural control while standing, while higher percentages define asymmetry and poor postural control. Postural Symmetry (%) = Weight on Paralytic Side / Body Weight - 0.5| x 100 Weight Transfer Symmetry = Weight on Intact Side - Weight on Paralytic Side (%) Total Body Weight.

3. The Postural Assessment Scale (PASS)

   Time frame: day 1

   The PASS contains 12 items that measure a person's balance performance in situations of varying difficulty, such as lying, sitting, standing or changing standing position. The scale is administered under two main headings: during posture maintenance and posture change. Sitting without support, standing with support, standing without support, standing on paretic and nonparetic legs are the balance assessments under the heading of maintaining posture. Lateral rotation from supine to paretic and nonparetic side, lateral rotation from supine to sitting, from sitting to supine, from sitting to supine, from sitting to supine, from sitting to standing, from standing to sitting, and picking up a pen on the floor while standing are balance assessments under the heading of posture change. The scale is evaluated between 0-36. The feasibility of the movement is tested between 0-3; "0" is the lowest value; "3" is the highest value

4. MINI-BEST TEST

   Time frame: day 1

   Mini-BEST Test will be used to determine balance level. It consists of 4 sub-parameters including preparatory movement, reactive postural control, sensory orientation, dynamic walking and a total of 14 items. It is a test that is evaluated over a total of 28 points and requires an average of 10-15 minutes. High score indicates high function

5. Functional reach test (FRT)

   Time frame: day 1

   It is used to measure both the individual's functional balance and the amount of dynamic reaching. Patients will first be asked to extend their arm straight forward and the distance they reach will be recorded. They will then be asked to reach as far as they can reach forward without lifting their heels off the floor. The maximum value at which he/she can reach and return to his/her original position without losing his/her balance will be measured. Repeating 3 times, these three values will be averaged

6. Timed Up and Go Test (TUG)

   Time frame: day 1

   The timed stand and walk test (STWT) is used to assess timed performance. In the application, the individual first gets up from the chair, walks 3 meters, then walks back to the same chair and sits down again. The patient's time to complete the test is measured with a stopwatch. Measuring the time taken during this performance is used to determine the functional mobility of the person. Accordingly, completing the task in ≤ 10 seconds indicates that functional mobility is normal, completing the task in 10-20 seconds indicates that mobility is good, the person can walk with or without a device, can go out alone, completing the task in 20-30 seconds indicates that there is a serious problem with mobility and that the person performs mobility using an assistive device.

7. 6 Minute Walk Test(6MWT)

   Time frame: day 1

   6 Minute Walk Test (6MWT): Physiological expenditure index (PEI) will be calculated to evaluate the energy expenditure and walking effort of individuals during the test. During the test, individuals will be asked to walk as fast as possible in a 30-meter straight corridor. Individuals will be told that if they feel tired or breathless during the test, they can rest or stop the test. Standard words of encouragement are used during the test. At the end of the test, the 6MWT distance is recorded in meters. Using age and gender, 6MWT expected values and 6MWT distance (% 6MWT) values expressed as a percentage of the expected values (6MWT distance * Body weight (kg)) are calculated. A 6MWT distance of less than 82% indicates a reduced functional capacity

8. The Five Times Sit to Stand Test (5xSTS)

   Time frame: day 1

   For the test, the individual is asked to sit on a chair with a height of 43.18 (12 inches) cm with the back straight, feet in contact with the floor and arms crossed on the chest. The individual is asked to sit on and stand up from the chair 1 time for a trial. After the trial performance, he/she is instructed to sit on the chair and stand up as quickly as possible and without stopping, and the elapsed time at the end of the fifth repetition is recorded. Validity and reliability studies were conducted in individuals with stroke 20-29 yrs ⇒ 6.0±1.4 sec 30-39 yrs ⇒ 6.1±1.4 sec 40-49 yrs ⇒ 7.6±1.8 sec 50-59 yrs ⇒ 7.7±2.6 sec 60-69 yrs ⇒ 8.4±0.0 sec (male), 12.7±1.8 sec (female) 70-79 yrs ⇒ 11.6±3.4 sec (male), 13.0±4.8 sec (female) 80-89 yrs ⇒ 16.7±4.5 sec (male), 17.2±5.5 sec (female) 90+ yrs ⇒ 19.5±2.3 sec (male), 22.9±9.6 sec (female)

9. Measurement of the craniovertebral angle

   Time frame: day 1

   Measurement of the craniovertebral angle; the patient is asked to find the most natural position by flexion and extension of the head in the standing position and a photograph is taken with a digital camera from a distance of 1.5 m to the shoulder level of the patient and this process is repeated 3 times. The images obtained are then digitally calculated with the help of an appropriate program.